Error "printhead not installed" 1401 1403 1405 on Canon printers

The printhead is probably broken.

The last thing to try:

• Remove the cartridges
• Remove the printhead
• Power off the printer and wait a minute;
• Power on.
• Installe the printhead and the cartridges.
• if you are Still facing same problem Call Canon Expert : +1-855-517-2433 

How to Fix Error 1003/E02 in Canon MX Series Printers.

1003/E02 - Orange light blinking 2 times

Description:

No paper in the cassette (paper tray).

Resolution:

1.      Insert paper into the cassette (paper tray).

2.      Press the [Resume/Cancel] button on the device to continue.

If the above solution has not resolved your error, please contact your nearest Canon authorised service facility. and Call Canon Help Center +1-855-517-2433.

Canon Pixma MX340 printer. How to clear Error 5200?

1. Turn off the printer .

2. Press the Stop button for 2 second and hold it.

3. Press the On button, hold it and release the Stop button.

4. Press Stop button 5 times then release together, with the On button.

5. LCD display will blank and now reseting.

6. Computer will detect new hardware just ignore it.

7. Turn off the printer then turn it On.

If the error persists, the unit may require servicing to resolve the issue.  Please click on the Contact Us link below to obtain further assistance and servicing options if needed.

This didn't answer your question or issue? Find more help at Contact Us.

How to Fix Canon MP210 Ink Counter Reset

Canon MP210 Ink Counter Reset

The following procedures may be used to reset the Canon printer ink level monitoring following the installation of a refilled Canon 30, 31, 40, 41, 50, 51, 210, 211, 240, or 241 integrated ink cartridges. In most cases, the error/alert will need to be cleared to enable printing. Ink waste container reset procedures are also provided below.

NOTE: for multi-cartridge installation, the procedure(s) may need to be repeated twice.
or you call canon support at 855-517-2433

For PGI-5, PGI-9PBK, CLI-8, PGI-220 CLI-221 PGI-225 CLI-226 PGI-250 CLI-251 Cartridges:  These are new Canon cartridges which have an embedded chip on each cartridge. If you just refill the ink, the printer will still reads the cartridge as empty. You have two choices: Purchase a “refillable cartridge” any sellers.     These refillable cartridges have an auto-reset chip (non OEM) and will reset automatically. Use a chip resetter (e.g., search Canon + model number + resetter on eBay).     Follow the instruction below to refill your original cartridge, and use the resetter to reset the chip. If you Facing any Problem Call Canon Expert: 855-517-2433

How to Solve Error P,7 P7 or P07 (5B00) on Canon printers

Solution 1: If the device is not functioning properly or to clear memory, resetit.

• On the operator panel, press the button. (The display will go blank.) Note: It may be necessary to unplug the power cord if pressing the ON button does not shut off the printer.
• Wait approximately ten seconds and then press the button again.
• Wait until the device has completed its cycling process before submitting another job request. Note: It may be necessary to unplug the power cord and retry if the above steps do not clear the error.

Solution 2: 

Step 1: Entering Service Mode

• While the printer is OFF, press and hold the Start/Stop button (Resume/Cancel in some other models).
• While holding the Start/Stop button, press and hold the POWER button.
• When the POWER LED (green light) lit, release the Start/Stop button (still holding the POWER button).
• Press the Start/Stop button TWICE (still holding the POWER button)
• Release the POWER button.
• Wait for the LCD to display “0″ (zero).

Step 2: Using Resetter / Software

• Download Ressetter: http://www.ziddu.com/download/10241255/ServiceTool_1050.zip.html
• Run “service_tool 1050.exe”.
• Confirm detected USB-port numbers on USB port column.
• Click “Main button” on Clear ink counter section. Make sure there are papers in the paper feed because the printer will print after the process is complete.
• Click “platen button” on the “Clear ink counter” section. The printer will print again.
• Turn off the printer and then turn the printer on. You printer is ready for use.

How to Fix Error code U140 & U150 on canon printers

Solution 1:

• Open the paper output tray.

• Turn on the printer and open the scanning unit. The printer cartridge carriage will move to the center. Open the inner cover securing the cartridge in place by pulling it downward.

• Press the tab on the problematic ink cartridge and lift it to remove it from the printer. You will be able to tell which ink cartridge is causing the problem because its indicator light will be off or flashing.

• Open the replacement ink cartridge and pull the orange tape in the direction of the arrow to remove the protective film. Tear the orange tape off along the dotted line.
• Place the ink cartridges into the printer and press where indicated on the cartridge until it clicks into place. Ensure that all ink cartridges have a red indicator light showing that they are properly installed.

• Close the inner cover on the cartridge carriage and the scanning unit. The printer will automatically start a print head cleaning cycle. When the cleaning cycle is complete, the printer is ready to use.

Solution 2:

• Put the little green circuit board from the old ink cartridge of the same color in the new cartridge.
• If you are facing more problems Call Us +1-855-517-2433

How to Fix Error 1000 in Canon MX Series.

1000 - Orange light blinking 2 times

Description:

There is no paper in the rear paper tray at the back of the printer.

Resolution:

1.      Insert paper into the rear tray.

2.      Press the [Resume/Cancel] button on the device to continue.

If the above solution has not resolved your error, please contact your nearest Canon authorised service facility.

How to fix Error 6942 in Canon MX 370

Description:

USB sub-system timeout error

Resolution:

-> Power off the machine, and power it on again.

If the error still occurs, replace the part listed on the right (under “Parts to be replaced if the listed solutions are not effective”). 

How to Fix Error 1250/E17 in Canon MX Series Printers

1250/E17- Orange light blinking 3 times

Description:

The front door is closed.

Resolution:

1.      Open the front door to allow prints to exit.

Note - This error is detected at the start of printing or during printing.

If the above solution has not resolved your error, please contact +1-855-517-2433

How to Fix Error U072 on Canon printers

Solution 1:

• Open the cover
• Remove the cartridges.
• Power off the printer
• Power on the printer
• Réinstall the cartridges
• Close the cover.

Solution 2:

•  Verify that the ink tank are installed in the appropriate positions.
• Change the faulty cartridge

Solution 3:

• Clean the printhead
• If you are facing more problems Call Canon: +1-855-517-2433

Error code E000733-0001 on Canon IR2200

E733-0001 means a fault is detected by the main controller PCB in the communication between the DC controller PCB and the main controller PCB.

Main cause: The connector has poor connection. The DC controller PCB is faulty.

Solution:

Verify the connection between the connector J1015 on the main controller PCB and the conductor J316 on the DC controlled PCB is normal.
Correct the connection if necessary.

The connection is correct: Replace the DC controller PCB. 

post your question here  

How to solve error 6A90 or "APP sensor error" on Canon printers

Error code 6A90 or "APP sensorerror" occured during paper feeding or purging.

Solution 1:

• check for foreign material or paper debris around the purge drive system unit;
  - remove foreign material.

Solution 2:

• check for foreign material or paper debris around the ASF unit;
  - remove foreign material.

Solution 3:

• If other solution fail, replace one off the following part
• If you are Facing More Problems Call Canon Expert: 855-517-2433

Error code 6A80 on Canon printers

Solution 1:

• Switch the printer OFF
• Press buttons 1 + 2 + 3 and 4 (simultaneously using four fingers)
• Keep pressing this four buttons for 10 seconds
• Release the On/Off button (number 4) (Keeping pressing the others)
• After a few seconds (when the printer go ON), release buttons 1, 2, 3

Solution 2 (Thanks to Dick):

• I discovered that the head was blocked from moving all the way to the right by a white nylon lever and discovered that there was a thin, small pad that had come loose and was blocking the mechanism to activate the head motion. 
• One pad was about 1/2 inch by 1/2 inch and a second was a narrow 3/32 x 1/2 inch pad both about 1/16 thick. 
• I removed these pads and the printer returned to normal

·         Posta Question....

How to resolve error 6A80 on an MP560

Error 6A80

There are several reasons for error 6A80 to appear. This article provides you recommendations with links to clear the message.

To clear the error, click on the link to open the article and get detailed instructions.

Paper is jammed or there is an objectinside the printer

NOTE

ISSUES: 

If you need to turn off the machine to remove jammed paper during printing, press the Stop button to cancel print jobs before turning off the machine

Cause: Paper Is Jammed in the Paper Output Slot or the RearTray

Post a Question Here...

 CALL US +1-855-517-2433 (TOLL FREE)

Configure Silex C-6700WG Print Server through a Wireless LAN

If a firewall function of commercial security software is used, disable the firewall function while configuring this product. Refer to the "Discovery Check List" section of Troubleshooting in the Users Manual.The following items are required in order to connect this product to a network.USB Cable


Use to connect this product and a printer.There is no need to purchase a new USB cable when a cable was bundled with the printer to be connected to this printer.Connect the AC adapter to this product and the power plug to the outlet.

Verify the Wireless LED(Green) blinks.

Insert the CD-ROM (CX User Software) into your Windows PC. Click OK.

Startup menu is displayed. Click Print Server Setup.

Click Wireless.

In a Windows XP environment (SP2 or higher), the following message will be displayed. Select Yes.

The User Account Control screen is displayed when configuration is performed on Windows Vista. Select Continue.CX Wireless Setup screen is displayed. Select Configure print server wirelessly from your computer and click Next.

Read the SOFTWARE LICENSE AGREEMENT and click Yes.
If two or more network cards are installed in the PC, the screen below is displayed to select the network card to be used. Select the wireless network card to be used and click OK.

If the screen below is displayed, you need to change the wireless settings on the PC manually. Click OK.

If the wireless settings on the PC differ from the configuration information on the screen below, change the PC wireless settings to match those displayed on the screen below.Verify the wireless settings on the PC and click Next.

If you use Windows XP and the setup utility automatically changed the wireless settings on the PC, this screen is not displayed. Proceed to 10 in this section.Select a printer to be configured and click Next.

If your printer is not displayed on the list, click Refresh.If this does not help, refer to the "Discovery Check List" section of Troubleshooting in the Users Manual.It is set to use TCP/IP. Please do the setting that exists in the environment used.If you are not sure how to determine the IP address to set, refer to "How should I determine the way to assign IP address to this product?" in the Q&A section of the Troubleshooting chapter in the Users Manual<< For the environment with a DHCP server >>Select Get IP Address Automatically and click Next.

The IP address assigned by DHCP server may possibly be changed.When managing an IP address using a DHCP server, the DHCP server needs to be configured to assign a static IP address for this printer.<< Assign an IP address manually >>Select Assign IP Address and enter the designated IP address. Click Next.

The IP address used in the above screen is a sample address. Please specify an IP address appropriate to your environment.Enter Subnet Mask and Default Gateway as appropriate.When you will use this product in the wireless network, select the wireless network that you wish to use from the list, enter the wireless network key and click Next.

If the wireless network that you wish to use is not shown in the list, click Detailed Config and configure each setting.

Please refer to the following information to configure the wireless network setting.< Communicate via an access point >

Wireless Mode	Select Infrastructure.
SSID	Enter the same SSID as the access point.
When encrypting communication using WEP
Network Authentication	Select Open. (If the access point is set to use the Pre-Shared key, select Shared)
Use WEP	Select ON.
Key Size	Set the same WEP key size as the access point (64bit/128bit). To enter a WEP key by a string, select 64bit (ASCII) or 128bit (ASCII). To enter a WEP key by a number, select 64bit (hexadecimal) or 128bit (hexadecimal).
WEP Key	Enter the same WEP key as the access point.
Key Index	Select the same Key index as the access point.
When encrypting communication using WPA
Network Authentication	Select WPA.
Encryption Mode	Select the same encryption mode as the access point (TKIP / AES).
Pre-Shared Key	Enter the same Pre-Shared key as the access point.
When using no encryption
Network Authentication	Select Open.
Use WEP	Select OFF.

< Communicate directly with PC >

Wireless Mode	Select AdHoc.
SSID	Enter the same SSID as the communication device.

Channel	Enter the same channel as the communication device.
When encrypting communication
Network Authentication	Select Open.
Use WEP	Select ON.
Key Size	Enter the same WEP key size as the communication device (64bit/128bit). To enter a WEP key by a string, select 64bit (ASCII) or 128bit (ASCII). To enter a WEP key by a number, select 64bit (hexadecimal) or 128bit (hexadecimal).
WEP Key	Enter the same WEP key as the communication device.
Key Index	Select the same Key index as the communication device.
When using no encryption
Network Authentication	Select Open.
Use WEP	Select OFF.

Confirm the configuration parameters and click Execute.

The contents included in this screen will vary depending on the item you have configured.Configuration is completed.<< If you did not change the wireless settings on the PC manually >>Select Yes or No and click Finish.

If you selected Yes, refer to the "Install the Applications" attachment below and proceed with the installation.<< If you changed the wireless settings on the PC manually >>Click Finish

Reset the wireless settings on the PC to match your network environment. Refer to the "Install the Applications" attachment below and proceed with the installation.Connect the USB device to be shared over the network to this printer with USB cable.

Configuration is complete.

Post a Question....